SALDA AIR Android application

(Herunterladen) 

A SALDA AIR mobile application enables you to control SALDA air handling units from a smartphone or tablet.

Line below arrow

SALDA AIR iOS application

(Herunterladen) 

Line below arrow

SA-Control firmware 1.01.26

(Herunterladen) 

SA-Control firmware version for the panel with software 1.01.11 and lower. NOTE: if wrong file is uploaded to the controller, it will not boot properly and black screen will be shown. In this case, please, repeat the update procedure with another file

Line below arrow

SA-Control firmware 1.01.26

(Herunterladen) 

SA-Control firmware version for the panel with software 1.01.12 and higher. NOTE: if wrong file is uploaded to the controller, it will not boot properly and black screen will be shown. In this case, please, repeat the update procedure with another file

Line below arrow

VentMaster 5.17.0 build 3

(Herunterladen) 

Auslegungssoftware mit 3D-Visualisierung für Kastenklimageräte.

Historie

2020-06-02 Program updated to Version 5.17.0 build 2 Fixes: 1. Small fixes. 2020-05-20 Program updated to Version 5.17.0 build 1 Fixes: 1. Small fixes. 2020-05-15 Program updated to Version 5.17.0 Fixes: 1. AmberAir range. Added possibility to select high-efficiency pocket filters. These filters have energy-efficient filter media and more longer pockets than ordinary pocket filters. The new filters have lower pressure drop (therefore the AHU will consume less energy) and longer service life (less frequent filter changes will be required). In default settings form it is possible to select which filters (energy efficient or ordinary) will be added when selecting new air handling units (of course it is possible to change filter type later during unit selection). 2. Small fixes. 2020-05-12 Program updated to Version 5.16.1 build 1 Fixes: 1. Small fixes. 2020-04-17 Program updated to Version 5.16.1 Fixes: 1. AmberAir Compact CXP. Holmak heat exchangers models have been changed from TS* to GS* (same size and length). 2. Small fixes. 2020-04-14 Program updated to Version 5.16.0 build 1 Fixes: 1. Small fixes. 2020-04-10 Program updated to Version 5.16.0 Fixes: 1. AmberAir range. Added possibility to select ebm-papst direct-driven centrifugal fans with EC motors wall. 2. AmberAir range. FlaktWoods direct driven centrifugal fans with PM motors not available for selection anymore. 3. Small fixes. 2020-03-19 Program updated to Version 5.15.3 build 6 Fixes: 1. Small fixes. 2020-02-28 Program updated to Version 5.15.3 build 5 Fixes: 1. Small fixes. 2020-02-21 Program updated to Version 5.15.3 build 4 Fixes: 1. Small fixes. 2020-02-14 Program updated to Version 5.15.3 build 3 Fixes: 1. Small fixes. 2020-01-30 Program updated to Version 5.15.3 build 2 Fixes: 1. Small fixes. 2020-01-24 Program updated to Version 5.15.3 build 1 Fixes: 1. Small fixes. 2020-01-23 Program updated to Version 5.15.3 Fixes: 1. AmberAir Compact CXP. Holmak heat exchangers DLL have been updated to v2.0.0.9. 2. Small fixes. 2020-01-17 Program updated to Version 5.15.2 build 1 Fixes: 1. Small fixes. 2020-01-10 Program updated to Version 5.15.2 Fixes: 1. AmberAir Range. Performance corrections have been made according Eurovent Real Unit test results. 2. AmberAir and AmberAir Compact range. HeatRun heat exchangers dll have been updated to v1.7.4.0. Water heater capacity was slightly adjusted. 3. Small fixes. 2020-01-06 Program updated to Version 5.15.1 build 2 Fixes: 1. Small fixes. 2019-12-20 Program updated to Version 5.15.1 build 1 Fixes: 1. Small fixes. 2019-12-06 Program updated to Version 5.15.1 Fixes: 1. AmberAir range. Energy Recovery company (ERI Corporation S.r.L.) have been chosen as main supplier for counterflow heat exchanger. Recutech counterflow heat exchangers not available for selection anymore. 2. Small fixes. 2019-11-20 Program updated to Version 5.15.0 build 1 Fixes: 1. Small fixes. 2019-11-15 Program updated to Version 5.15.0 Changes: 1. AmberAir Compact range. Klingenburg heat exchangers DLL have been updated to v5.0.2. This affects efficiency of heat exchangers. 2. AmberAir range. Default supplier for direct-driven centrifugal fans with EC motor have been changed from Zhiell-Abbegg to FlaktWoods. 3. AmberAir range. Added possibility to select SIEMENS controller application by language type. 4. AmberAir range. Hoval rotary and plate heat exchangers dll have been updated to v2.0.4.0. Rotor housing has been improved. 2019-10-25 Program updated to Version 5.14.2 build 1 Fixes: 1. Small fixes. 2019-10-18 Program updated to Version 5.14.2 Fixes: 1. AmberAir range. Fisair evaporative humidifier dll have been updated to v3.4.0. 2. Small fixes. 2019-10-11 Program updated to Version 5.14.1 build 1 Fixes: 1. Small fixes. 2019-10-04 Program updated to Version 5.14.1 Changes: 1. AmberAir range. Added possibility to select frost protection thermostat on rail for water heater or reversible water cooler sections. Frost protection thermostat automatically selected for last water heater or reversible water cooler section in units with control system. And it is freely selectable in units without control system in each water heater or reversible water cooler section. 2019-09-27 Program updated to Version 5.14.0 build 1 Fixes: 1. Small fixes. 2019-09-06 Program updated to Version 5.14.0 Changes: 1. AmberAir range. Added possibility to select start-up filters set for ePM1 and ePM2.5 classes pocket filters sections. 2. AmberAir range. Added possibility to select lifting eyes for AHU sections. 3. AmberAir range. Added possibility to select purge sector for rotary heat exchangers. 4. The name of Luvata, a manufacturer of heating and cooling coils, has been changed to Modine. AmberAir range. Added possibility to select water heating coils and water cooling coils with turned tubes (90° inline or against airflow). 2019-08-19 Program updated to Version 5.12.22 build 5 Fixes: 1. Small fixes. 2019-08-09 Program updated to Version 5.12.22 build 4 Fixes: 1. Small fixes. 2019-07-12 Program updated to Version 5.12.22 build 3 Fixes: 1. Small fixes. 2019-06-28 Program updated to Version 5.12.22 build 2 Fixes: 1. Small fixes. 2019-05-29 Program updated to Version 5.12.22 build 1 Fixes: 1. Small fixes. 2019-05-24 Version 5.12.22 Changes: 1. AmberAir range. Added possibility to select fans with short lead time. 2. AmberAir range. Pressure gauge in fan section has been changed to air flow meter. 2019-05-17 Program updated to Version 5.12.21 build 1 Fixes: 1. Small fixes. 2019-05-10 Version 5.12.21 Changes: 1. AmberAir range. Zhiell-Abegg fans dll have been updated to v1.01 (190416). Article numbers was changed for some fans with ATEX motors and with IE3 motors. 2. AmberAir Compact CXV and CXH range: - Henceforth air temperature sensor is integrated after heat exchanger; - Added possibility to select control by constant air pressure or constant air flow; - Added possibility to select monitoring type of filters and heat exchanger: by pressure relay or Modbus pressure sensors. 2019-04-26 Version 5.12.20 Changes: 1. AmberAir and AmberAir Compact range. Recutech heat exchangers dll have been updated to v7.2.0. This affects efficiency of heat exchangers. 2019-04-16 Program updated to Version 5.12.19 build 2 Fixes: 1. Small fixes. 2019-04-09 Program updated to Version 5.12.19 build 1 Fixes: 1. Small fixes. 2019-04-05 Version 5.12.19 Changes: 1. AmberAir Compact range. Added possibility to select counter flow heat exchangers from new supplier: Holmak. 2019-03-22 Version 5.12.18 Changes: 1. AmberAir range. FläktWoods fans dll have been updated to version 4.8.1.9d. GMEC-3 new ordering codes ending ..01 (old: ..00). The spider construction has been updated. 2. AmberAir range. Heatex rotary heat exchangers dll have been updated to v516. The performance data of all rotary heat exchangers have been updated. 2019-03-06 Program updated to Version 5.12.17 build 1 Fixes: 1. Small fixes. 2019-03-01 Version 5.12.17 Changes: 1. AmberAir range. Added possibility to select condensing gas-fired heaters (from 5-KR unit size). Heaters capacity up to 360kW. 2. AmberAir and AmberAir Compact range. The logic for choosing the temperature control point RMG for water heater and cooler has been changed. 2019-02-22 Program updated to Version 5.12.16 build 1 Fixes: 1. Small fixes. 2019-02-15 Version 5.12.16 Changes: 1. AmberAir range. Hoval rotary and plate heat exchangers dll have been updated to v2.0.3.0. This affects rotary heat exchangers efficiency. Also bug with wrong pressure drop for plate heat exchangers was fixed. 2. AmberAir and AmberAir Compact range. HeatRun heat exchangers dll have been updated to v1.7.1.0. Bugs fixes. 3. AmberAir Compact range. Frames material for panel filters changed to galvanized steel. 2019-01-23 Program updated to Version 5.12.15 build 3 Fixes: 1. Small fixes. 2019-01-23 Program updated to Version 5.12.15 build 2 Fixes: 1. Small fixes. 2019-01-08 Program updated to Version 5.12.15 build 1 Fixes: 1. Small fixes. 2019-01-04 Version 5.12.15 Changes: 1. AmberAir range. Zhiell-Abegg fans dll have been updated to v1.01 (181214). Power input for direct-driven fans with AC motors was adjusted with AC technology tolerance limits. 2. AmberAir range. Belt-driven centrifugal fans have been discontinued. 3. Small fixes. 2018-12-14 Version 5.12.14 Changes: 1. AmberAir and AmberAir Compact range. The electric heater calculation logic has been changed. 2. AmberAir range. Fan section with small plug fans length was slightly increased. 3. Small fixes. 2018-12-11 Program updated to Version 5.12.13 build 1 Fixes: 1. Small fixes. 2018-12-07 Version 5.12.13 Changes: 1. AmberAir and AmberAir Compact range. Pocket filters classes and data was adjusted for ePM1 and ePM2.5 filters according to measurements results at independent certified laboratory. ePM2.5 60% became ePM2.5 65%, ePM2.5 80% became ePM2.5 90% and ePM1 75% became ePM1 85%. 2. AmberAir and AmberAir Compact range. Recutech heat exchangers dll have been updated to v7.0.0. This affects efficiency of heat exchangers. 3. Small fixes. 2018-11-23 Program updated to Version 5.12.12 build 1 Fixes: 1. Small fixes. 2018-11-16 Version 5.12.12 Changes: 1. AmberAir and AmberAir Compact range. HeatRun heat exchangers dll have been updated to v1.7.0.0. Added possibility to calculate heating coils with negative water temperature out. 2. Small fixes. 2018-11-13 Program updated to Version 5.12.11 build 4 Fixes: 1. Small fixes. 2018-11-09 Program updated to Version 5.12.11 build 3 Fixes: 1. Small fixes. 2018-11-02 Program updated to Version 5.12.11 build 2 Fixes: 1. Small fixes. 2018-10-26 Program updated to Version 5.12.11 build 1 Fixes: 1. Small fixes. 2018-10-22 Version 5.12.11 Changes: 1. AmberAir and AmberAir Compact range. HeatRun heat exchangers dll have been updated to v1.6.8.0: minor internal fixes. 2. Small fixes. 2018-10-18 Program updated to Version 5.12.10 build 1 Fixes: 1. Small fixes. 2018-10-12 Version 5.12.10 Changes: 1. AmberAir range. Energy Recovery counter flow heat exchangers dll have been updated to v1.0.3.67. Bugs fixes. 2. Small fixes. 2018-10-05 Program updated to Version 5.12.9 build 2 Fixes: 1. Small fixes. 2018-10-02 Program updated to Version 5.12.9 build 1 Fixes: 1. Small fixes. 2018-09-28 Version 5.12.9 Changes: 1. AmberAir range. Selection of gas-fired heaters no more available. 2. Small fixes. 2018-09-25 Program updated to Version 5.12.8 build 1 Fixes: 1. Small fixes. 2018-09-21 Version 5.12.8 Changes: 1. AmberAir range. Heatex rotary heat exchangers Q2A, Q2E, Q2K (divided) have been discontinued. 2. AmberAir range. Luvata heat exchangers dll have been updated to v9.5.14.0. This affects prices. 3. Small fixes. 2018-09-19 Program updated to Version 5.12.7 build 1 Fixes: 1. Small fixes. 2018-09-14 Version 5.12.7 Changes: 1. AmberAir range. Fisair evaporative humidifier dll have been updated to v3.2.5. This affects prices. 2. Small fixes. 2018-09-07 Version 5.12.6 Changes: 1. Selection of Flex remote control no more available with MCB control system. 2. Small fixes. 2018-09-03 Program updated to Version 5.12.5 build 1 Fixes: 1. Small fixes. 2018-08-24 Version 5.12.5 Changes: 1. AmberAir range. Added possibility to select direct-driven centrifugal fan with EC motor from FlaktWoods (from 3-KR unit size). 2. AmberAir range. FläktWoods fans dll have been updated to version 4.8.1.5d. This affects fans sound data. 3. AmberAir range. Heatex rotary heat exchangers dll have been updated to v515. This affects efficiency of wheels with 1.4mm gap. 4. Small fixes. 2018-08-22 Program updated to Version 5.12.4 build 2 Fixes: 1. Small fixes. 2018-08-17 Program updated to Version 5.12.4 build 1 Fixes: 1. Small fixes. 2018-08-10 Version 5.12.4 Changes: 1. AmberAir range. Selection of direct-driven centrifugal fan with EC motor no more available in 2-KR size unit. Choose direct-driven centrifugal fans with EC motors wall instead of it (with motor voltage 1~230V). AmberAir range. Added selection of direct-driven centrifugal fans with EC motor wall selection for 1-KR size units (with motor voltage 1~230V). AmberAir range. Sections lengths adjusted for direct-driven centrifugal fans with EC motor wall. 2. Small fixes. 2018-08-06 Program updated to Version 5.12.3 build 1 Fixes: 1. Small fixes. 2018-08-03 Version 5.12.3 Changes: 1. Performance corrections have been made according Eurovent ModelBoxes tests results: - MD50+ thermal bridging factor class changed to TB2; - Changed acoustical insulation values for SD50, MD50 and MD50+ casings. 2. Small fixes. 2018-08-02 Program updated to Version 5.12.2 build 5 Fixes: 1. Small fixes. 2018-07-30 Program updated to Version 5.12.2 build 4 Fixes: 1. Small fixes. 2018-07-27 Program updated to Version 5.12.2 build 3 Fixes: 1. Small fixes. 2018-07-25 Program updated to Version 5.12.2 build 2 Fixes: 1. Small fixes. 2018-07-23 Program updated to Version 5.12.2 build 1 Fixes: 1. Small fixes. 2018-07-20 Version 5.12.2 Changes: 1. AmberAir range. Added possibility to select direct driven fans with EC motors wall. 2. AmberAir range. RAL 7035 and RAL 9005 colors no more available for external panels. 3. AmberAir range. Hoval rotary and plate heat exchangers dll have been updated to v2.0.2.0. 4. Small fixes. 2018-07-13 Version 5.12.1 Changes: 1. Added possibility to select new remote control panel SA-Control with MCB controller. 2. AmberAir range. The direct-driven centrifugal fans can be selected with new higher efficiency ZAbluefin impellers (071, 080, 090, 100 and 110 size with IE3 motor). Thus Zhiell-Abegg fans dll have been updated to v1.01 (180712). 3. AmberAir range. Added possibility to choose in settings, which motor to use by default for direct-driven centrifugal fan: IE2 or IE3. 4. Small fixes. 2018-07-11 Program updated to Version 5.12.0 build 2 Fixes: 1. Small fixes. 2018-07-10 Program updated to Version 5.12.0 build 1 Fixes: 1. Small fixes. 2018-06-29 Version 5.12.0 Changes: 1. AmberAir range. Pre-filters and pocket filters has been changed. From now on, the filter classes correspond to the new filter standard ISO 16890. For customer convenience, the brackets indicate the filter's equivalent according to the old standard EN 779. Since filter materials have been changed, the pressure drop for new filters differs from the old ones. 2. PRV selection not be available from 2018-07-01 2018-06-22 Program updated to Version 5.11.1 build 2 Fixes: 1. Small fixes. 2018-06-13 Program updated to Version 5.11.1 build 1 Fixes: 1. Small fixes. 2018-06-08 Version 5.11.1 Changes: 1. AmberAir range. HeatRun heat exchangers dll have been updated to v1.6.7.0: a. Fixed heaters error, which sometimes calculated negative humidity value; b. Increasing the accuracy of the heater calculation by replacing the water step from 5% to 1%. 2. Small fixes. 2018-06-05 Program updated to Version 5.11.0 build 1 Fixes: 1. Small fixes. 2018-06-01 Version 5.11.0 Changes: 1. AmberAir range. Added possibility to select counter flow heat exchangers from new supplier: Energy Recovery. New counter flow heat exchangers available for all unit sizes. 2. AmberAir Compact range. Added possibility to select unit with rotor heat exchanger. Available only size 7. 3. Small fixes. 2018-05-29 Program updated to Version 5.10.1 build 4 Fixes: 1. Small fixes. 2018-05-28 Program updated to Version 5.10.1 build 3 Fixes: 1. Small fixes. 2018-05-22 Program updated to Version 5.10.1 build 2 Fixes: 1. Small fixes. 2018-05-22 Program updated to Version 5.10.1 build 1 Fixes: 1. Small fixes. 2018-05-18 Version 5.10.1 Changes: 1. AmberAir range. Added possibility to select DBM heat recovery coils with polyester-coated aluminium fins. 2. Small fixes. 2018-05-16 Program updated to Version 5.10.0 build 4 Fixes: 1. Small fixes. 2018-05-11 Program updated to Version 5.10.0 build 3 Fixes: 1. Small fixes. 2018-05-09 Program updated to Version 5.10.0 build 2 Fixes: 1. Small fixes. 2018-05-08 Program updated to Version 5.10.0 build 1 Fixes: 1. Small fixes. 2018-05-04 Version 5.10.0 Changes: 1. AmberAir range. ModelBoxes changed. Now it is possible to choose four different ModelBoxes: - SD50+ (profiles without thermal bridge, polyurethane foam insulation), - SD50 (profiles with thermal bridge, polyurethane foam insulation), - MD50+ (profiles without thermal bridge, rock wool insulation), - MD50 (profiles with thermal bridge, rock wool insulation). It is possible to choose default ModelBox type in program settings. 2. AmberAir range. HeatRun heat exchangers dll have been updated to v1.6.6.0. 3. AmberAir Compact CXP. Performance corrections have been made according Eurovent Real Unit test results. 4. Small fixes. 2018-04-27 Program updated to Version 5.9.19 build 4 Fixes: 1. Small fixes. 2018-04-23 Program updated to Version 5.9.19 build 3 Fixes: 1. Small fixes. 2018-04-20 Program updated to Version 5.9.19 build 2 Fixes: 1. Small fixes. 2018-04-17 Program updated to Version 5.9.19 build 1 Fixes: 1. Small fixes. 2018-04-13 Version 5.9.19 Changes: 1. AmberAir range: Added possibility to select air handling units intended for ventilation of pools premises. 2. Small fixes. 2018-04-09 Program updated to Version 5.9.18 build 1 Fixes: 1. Small fixes. 2018-04-06 Version 5.9.18 Changes: 1. AmberAir range. Added possibility to select DBM heat recovery coils. 2. AmberAir Compact CXP. Changed modelbox CD50 data: D1, L1/L2, F9, T3, TB2. 3. Small fixes. 2018-03-30 Program updated to Version 5.9.17 build 3 Fixes: 1. Small fixes. 2018-03-27 Program updated to Version 5.9.17 build 2 Fixes: 1. Small fixes. 2018-03-26 Program updated to Version 5.9.17 build 1 Fixes: 1. Small fixes. 2018-03-23 Version 5.9.17 Changes: 1. AmberAir range. Heatex rotary heat exchangers dll have been updated to v514. 2. Small fixes. 2018-03-16 Version 5.9.16 Changes: 1. Selected AHU report corrections have been made according to Eurovent audit results. 2. Small fixes. 2018-03-09 Program updated to Version 5.9.15 build 4 Fixes: 1. Small fixes. 2018-03-02 Program updated to Version 5.9.15 build 3 Fixes: 1. Small fixes. 2018-02-27 Program updated to Version 5.9.15 build 2 Fixes: 1. Small fixes. 2018-02-26 Program updated to Version 5.9.15 build 1 Fixes: 1. Small fixes. 2018-02-23 Version 5.9.15 Changes: 1. AmberAir range. Controllers RREG and RHX2M for rotary heat exchangers changed to DRHX. 2. Small fixes. 2018-02-20 Program updated to Version 5.9.14 build 3 Fixes: 1. Small fixes. 2018-02-15 Program updated to Version 5.9.14 build 2 Fixes: 1. Small fixes. 2018-02-09 Program updated to Version 5.9.14 build 1 Fixes: 1. Small fixes. 2018-02-02 Version 5.9.14 Changes: 1. AmberAir range. Flaktwoods CENTRIFLOW (GPPM) fan range has been changed to more efficient CENTRIFLOW 3D (GMPM) fan range. 2. Small fixes. 2018-01-26 Version 5.9.13 Changes: 1. AmberAir range. Hoval rotary and plate heat exchangers dll have been updated to v2.0.1.0. Some plate gaps have been discontinued for plate heat exchangers. 2. Small fixes. 2018-01-24 Program updated to Version 5.9.12 build 5 Fixes: 1. Small fixes. 2018-01-19 Program updated to Version 5.9.12 build 4 Fixes: 1. Small fixes. 2018-01-18 Program updated to Version 5.9.12 build 3 Fixes: 1. Small fixes. 2018-01-16 Program updated to Version 5.9.12 build 2 Fixes: 1. Small fixes. 2018-01-12 Program updated to Version 5.9.12 build 1 Fixes: 1. Small fixes. 2017-12-22 Version 5.9.12 Changes: 1. AmberAir range. On/Off control for gas fired heaters are no longer available. 2. AmberAir range. HeatRun heat exchangers dll have been updated to v1.6.3.0. 3. AmberAir range. Luvata heat exchangers dll have been updated to v6.26.5.0. 4. AmberAir and AmberAir Compact range. Zhiell-Abegg fans dll have been updated to v1.01 (171129). 5. AmberAir and AmberAir Compact range. Recutech heat exchangers dll have been updated to v6.0.6.0. 6. Small fixes. 2017-12-18 Program updated to Version 5.9.11 build 1 Fixes: 1. Small fixes. 2017-12-15 Version 5.9.11 Changes: 1. AmberAir range. Hygienic AHU selection updated according to updated Eurovent Hygienic Standard RS/6/C/011-2017. Cables and integrated control equipment are no longer forbidden for hygienic units. 2. Small fixes. 2017-12-13 Program updated to Version 5.9.10 build 2 Fixes: 1. Small fixes. 2017-12-12 Program updated to Version 5.9.10 build 1 Fixes: 1. Small fixes. 2017-12-08 Version 5.9.10 Changes: 1. AmberAir range. Added possibility to choose pressure transmitter with display for filters pressure drop visual signaling and alarm to control system at the same time. 2. Small fixes. 2017-12-04 Program updated to Version 5.9.9 build 1 Fixes: 1. Small fixes. 2017-12-01 Version 5.9.9 Changes: 1. AmberAir range. Optimized selection to comply with ErP 2018 (COMMISSION REGULATION (EU) No 1253/2014). 2. AmberAir range. Added possibility to input desired efficiency for plate and rotary heat exchangers. The program automatically selects the heat exchanger parameters according to the desired efficiency. 3. AmberAir range. Added possibility to save default settings (air parameters, heat recovery efficiency and other) for new AHU. Added possibility to input airflow in m3/s or l/s. 2017-11-28 Program updated to Version 5.9.8 build 1 Fixes: 1. Small fixes. 2017-11-24 Version 5.9.8 Changes: 1. AmberAir range. Possibility to select HeatRun water cooler coils. Luvata coils available to select only with epoxy coating. 2. VSD supplier for the fans has been changed to ABB. 3. Selection of the distance between supply and exhaust parts of the AHU with heat recovery coils has been added to control selection. 4. Small fixes. 2017-11-21 Program updated to Version 5.9.7 build 5 Fixes: 1. Small fixes. 2017-11-17 Program updated to Version 5.9.7 build 4 Fixes: 1. Small fixes. 2017-11-13 Program updated to Version 5.9.7 build 3 Fixes: 1. Small fixes. 2017-11-09 Program updated to Version 5.9.7 build 2 Fixes: 1. Small fixes. 2017-11-06 Program updated to Version 5.9.7 build 1 Fixes: 1. AmberAir Compact CXP range. Klingenburg counter flow heat exchangers dll have been updated to v4.4 10/2017. 2. Small fixes. 2017-11-03 Version 5.9.7 Changes: 1. AmberAir range. For sections with doors added possibility to select between door (non-lockable type A or lockable type B) and removable hatch (type C). 2. AmberAir range. Improved design of segmented roof for outdoor units. 3. AmberAir Compact range. Total power and total current are included in the report. 2017-10-31 Program updated to Version 5.9.6 build 2 Fixes: 1. Small fixes. 2017-10-30 Program updated to Version 5.9.6 build 1 Fixes: 1. Small fixes. 2017-10-27 Version 5.9.6 Changes: 1. AmberAir range. Added possibility to choose units intended to use in coastal climate. 2. AmberAir range. New orders confirmation system have been launched. 3. DXF, REVIT files export bug fix for AmberAir Compact air handling units. 2017-10-24 Program updated to Version 5.9.5 build 1 Fixes: 1. Small fixes. 2017-10-20 Version 5.9.5 Changes: 1. AmberAir range. Improved control system section design. 2. AmberAir Compact range. Changed electric preheater calculation algorithm. 2017-10-16 Program updated to Version 5.9.4 build 1 Fixes: 1. Small fixes. 2017-10-13 Version 5.9.4 Changes: 1. AmberAir range. Added possibility to select rotary heat exchanger section with additional space for exchanger maintenance. 2. Added FLEX MCB remote controller compatible with MCB control board. 2017-10-06 Program updated to Version 5.9.3 build 2 Fixes: 1. Small fixes. 2017-10-02 Program updated to Version 5.9.3 build 1 Fixes: 1. Small fixes. 2017-09-29 Version 5.9.3 Changes: 1. Software calculation speed optimized. 2. AmberAir range. Heatex rotary heat exchangers dll have been updated to v5.13.01. 2017-09-22 Version 5.9.2 Changes: 1. AmberAir Compact range. Added possibility to calculate AHU LCC (life cycling cost) according to Eurovent 6/8 recommendations. 2. AmberAir Compact range. Added possibility to select Flex remote control in MCB control system accessories. 3. Small fixes. 2017-09-21 Program updated to Version 5.9.1 build 2 Fixes: 1. Small fixes. 2017-09-18 Program updated to Version 5.9.1 build 1 Fixes: 1. Small fixes. 2017-09-15 Version 5.9.1 Changes: 1. Controller RHX2M-1212 for rotary heat exchangers changed to RREG-4-0-0 for AmberAir range. 2. Small fixes. 2017-09-13 Program updated to Version 5.9.0 build 1 Fixes: 1. Small fixes. 2017-09-08 Version 5.9.0 Changes: 1. AmberAir range. Possibility to select new type of base frame and new type of base foot. 2. AmberAir range. Optimized pocket filters pressure drops due improved pocket filters quality. Filter Pocket Sewing Unit KL 970 ensures all filters pocket extra high quality. 3. AmberAir range. Possibility to select casing connection type: open or flanged. 4. AmberAir range. Compressors manufacturer have been changed for rotary heat exchanger with heat pump section. 5. Small fixes. 2017-09-01 Version 5.8.9 Changes: 1. AmberAir range. Fan chart with working point added to program and report. 2. AmberAir Compact CXP range. Added possibility to select the Right maintenance side. 3. AmberAir Compact CXP range. Added possibility to select the Horizontal configuration. 4. AmberAir Compact CXP range. Updated water heater coils selection list for Left maintenance side. 5. Small fixes. 2017-08-25 Version 5.8.8 Changes: 1. AmberAir range. Added possibility to select drip tray for pocket filter section. 2. AmberAir range. Added possibility to move a one-level component (right-click on component). 3. Small fixes. 2017-08-18 Program updated to Version 5.8.7 build 1 Fixes: 1. Small fixes. 2017-08-11 Version 5.8.7 Changes: 1. Added possibility to select new Eurovent certified AHU compact range: AmberAir Compact CXH. 2. AmberAir Compact range. Changed the algorithm of sound power calculation. 3. AmberAir Compact range. Updated water heater coils selection list for AmberAir Compact CXP. 4. Small fixes. 2017-08-04 Program updated to Version 5.8.6 build 1 Fixes: 1. Small fixes. 2017-07-28 Version 5.8.6 Changes: 1. AmberAir range. Added possibility to select U-tube manometer or pressure gauge for filter section. 2017-07-26 Program updated to Version 5.8.5 build 2 Fixes: 1. Small fixes. 2017-07-24 Program updated to Version 5.8.5 build 1 Fixes: 1. Small fixes. 2017-07-21 Version 5.8.5 Changes: 1. AmberAir range. Added possibility to choose internal panels material for individual parts of the unit: the bottom, top, front and rear. It is possible to select material for whole unit and for each section separately (right-click on section). 2. AmberAir range. Added possibility to choose material of internal metallic parts for filter section and for silencer section. 3. AmberAir range. Added possibility to choose drip tray material for sections with drip tray. 4. Added possibility to choose anodized casing profiles for SW50+ casing. 2017-07-17 Program updated to Version 5.8.4 build 1 Fixes: 1. Small fixes. 2017-07-14 Version 5.8.4 Changes: 1. Added possibility to select drip tray for service section. 2017-07-11 Program updated to Version 5.8.3 build 6 Fixes: 1. Some water heater coils removed from AmberAir Compact selection. 2017-07-05 Program updated to Version 5.8.3 build 5 Fixes: 1. Small fixes. 2017-07-05 Program updated to Version 5.8.3 build 4 Fixes: 1. Small fixes. 2017-07-05 Program updated to Version 5.8.3 build 3 Fixes: 1. Small fixes. 2017-07-05 Program updated to Version 5.8.3 build 2 Fixes: 1. Small fixes. 2017-07-04 Program updated to Version 5.8.3 build 1 Fixes: 1. Small fixes. 2017-06-30 Version 5.8.3 Changes: 1. Added possibility to select droplet eliminator with drip tray section. 2. Added calculation of the Eco-design requirements for AmberAir Compact range at the working point (not only for the maximum working point as it was before). 3. Changed the algorithm of preheater calculation for AmberAir Compact range. 2017-06-23 Version 5.8.2 Changes: 1. Coils and drip tray pipes location added to AHU drawings. 2. Coils fins and tubes material added to program and report. 3. Small fixes. 4. Added Italian language support. 2017-06-22 Program updated to Version 5.8.1 build 4 Fixes: 1. Small fixes. 2017-06-16 Program updated to Version 5.8.1 build 3 Fixes: 1. Small fixes. 2017-06-14 Program updated to Version 5.8.1 build 2 Fixes: 1. Small fixes. 2017-06-13 Program updated to Version 5.8.1 build 1 Fixes: 1. Small fixes. 2017-06-09 Version 5.8.1 Changes: 1. Added possibility to select crossflow section. 2. AHU flow chart added to report. 3. Added possibility to delete selected section with keyboard delete button. 2017-06-02 Version 5.8.0 Changes: 1. Added possibility to select new Eurovent certified AHU compact range: AmberAir Compact CXV and CXPL (left version). 2. Added possibility to choose standby fan in direct driven fan section. 3. Added possibility to clear offer request history from selection file. 2017-05-30 Program updated to Version 5.7.8 build 1 Fixes: 1. Small fixes. 2017-05-26 Version 5.7.8 Changes: 1. Possibility to select rotary heat exchangers in side by side configuration. 2. HeatRun water heaters dll have been updated to v1.6.0. 2017-05-25 Program updated to Version 5.7.7 build 2 Fixes: 1. Small fixes. 2017-05-22 Program updated to Version 5.7.7 build 1 Fixes: 1. Small fixes. 2017-05-19 Version 5.7.7 Changes: 1. Added possibility to save several selected projects reports in one pdf from project explorer. 2. Added possibility to choose which chapters should be in printed report. 3. HeatRun water heaters dll have been updated to v1.5.9. 2017-05-17 Program updated to Version 5.7.6 build 6 Fixes: 1. Small fixes. 2017-05-15 Program updated to Version 5.7.6 build 5 Fixes: 1. Small fixes. 2017-05-12 Program updated to Version 5.7.6 build 4 Fixes: 1. Small fixes. 2017-05-11 Program updated to Version 5.7.6 build 3 Fixes: 1. Small fixes. 2017-05-10 Program updated to Version 5.7.6 build 2 Fixes: 1. Small fixes. 2017-05-08 Program updated to Version 5.7.6 build 1 Fixes: 1. Small fixes. 2017-05-05 Version 5.7.6 Changes: 1. Added possibility to calculate AHU LCC (life cycling cost) according to Eurovent 6/8 recommendations. 2. Changed height of AmberAir 6-KR SW50+ water heater. 2017-05-03 Program updated to Version 5.7.5 build 7 Fixes: 1. Small fixes. 2017-05-02 Program updated to Version 5.7.5 build 6 Fixes: 1. Small fixes. 2017-04-27 Program updated to Version 5.7.5 build 5 Fixes: 1. Small fixes. 2017-04-26 Program updated to Version 5.7.5 build 4 Fixes: 1. Small fixes. 2017-04-25 Program updated to Version 5.7.5 build 3 Fixes: 1. Fixed Hoval heat exchanger price request problem. 2017-04-21 Program updated to Version 5.7.5 build 2 Fixes: 1. Small fixes. 2017-04-19 Program updated to Version 5.7.5 build 1 Fixes: 1. Small fixes. 2017-04-14 Version 5.7.5 Changes: 1. Possibility to select counter flow heat exchangers in side by side configuration. 2. Possibility to input system pressure drop before the unit (ODA, ETA) and after the unit (SUP, EHA). 3. New AHU's sections labeling. 4. P-Touch selection discontinued. 5. Recutech counter flow heat exchangers dll have been updated to v6.0.5.0, some gaps changed. 6. Heatex rotary heat exchangers dll have been updated to v05.00.012, new 2.2mm gap added. 7. Hoval cross flow heat exchangers dll have been updated to v2.0.1.0, some gaps changed or added. 8. Possibility to order coordination service for larger (10-16 KR) rotary heat exchanger with heat pump sections. Service includes section assembly on-site coordination, consultations according to manufacturer technical issues. 2017-04-07 Program updated to Version 5.7.4 build 4 Fixes: 1. Small fixes. 2017-04-04 Program updated to Version 5.7.4 build 3 Fixes: 1. Fixed "Invalid floating point" error on loading heat recovery units 2. Small fixes. 2017-03-31 Program updated to Version 5.7.4 build 2 Fixes: 1. Small fixes. 2017-03-27 Program updated to Version 5.7.4 build 1 Fixes: 1. Small fixes. 2017-03-24 Version 5.7.4 Changes: 1. Rotary heat exchanger with heat pump selection extended from 9-KR to 16-KR. 2. Optimized selection of rotary heat exchanger with heat pump. 2017-03-23 Program updated to Version 5.7.3 build 3 Fixes: 1. Small fixes. 2017-03-22 Program updated to Version 5.7.3 build 2 Fixes: 1. Small fixes. 2017-03-21 Program updated to Version 5.7.3 build 1 Fixes: 1. Small fixes. 2017-03-17 Version 5.7.3 Changes: 1. Possibility to select and add to project SALDA chillers (CH) and condensing units (CU) if water or DX cooling coils have been chosen a. Possibility to select up to 2 condensing units when 2 stage DX coil have been chosen b. Possibility to select up to 30 accessories if chiller or condensing unit have been chosen c. All chillers have integrated water tanks and circulation pumps d. All chillers and condensing units have possibility to be connected to AHU for better control and monitoring e. Possibility to turn ON/OFF chiller or condensing unit by AHU control panel f. Possibility to get the alarm signal from chiller or condensing unit through AHU control panel 2. Performance corrections according Eurovent Real Unit test results. 2017-03-14 Program updated to Version 5.7.2 build 4 Fixes: 1. Small fixes. 2017-03-10 Program updated to Version 5.7.2 build 3 Fixes: 1. Small fixes. 2017-03-08 Program updated to Version 5.7.2 build 2 Fixes: 1. Small fixes. 2017-03-07 Program updated to Version 5.7.2 build 1 Fixes: 1. Small fixes. 2017-03-03 Version 5.7.2 Changes: 1. Possibility to select gas-fired heater with natural gas or propane gas burner. Indoor or outdoor versions. Nominal capacity from 11 to 600kW. Nominal airflow from 1500 to 50000 m3/h. Heating efficiency up to 91% 2. Possibility to select pressure gauge for direct driven fan. Pressure gauge located on the doors outside the fan section and shows airflow in m3/s and m3/h 3. Possibility to select printout language before print preview and printing. No need to change interface language if you need printout in other language 2017-03-02 Program updated to Version 5.7.1 build 3 Fixes: 1. Small fixes. 2017-02-28 Program updated to Version 5.7.1 build 2 Fixes: 1. Small fixes. 2017-02-27 Program updated to Version 5.7.1 build 1 Fixes: 1. Small fixes. 2017-02-24 Version 5.7.1 Changes: 1. Filter dimensions changed for AmberAir SW50. Now all filters have Eurovent dimensions (592x592, etc.) 2. Possibility to choose spare filters sets for all kind of filters 2017-02-17 Program updated to Version 5.7.0 build 5 Fixes: 1. Small fixes. 2017-02-10 Program updated to Version 5.7.0 build 4 Fixes: 1. Small fixes. 2017-02-08 Program updated to Version 5.7.0 build 3 Fixes: 1. Small fixes. 2017-02-07 Program updated to Version 5.7.0 build 2 Fixes: 1. Small fixes. 2017-02-07 Program updated to Version 5.7.0 build 1 Fixes: 1. Small fixes. 2017-02-03 Version 5.7.0 Changes: 1. SmartAir brand changed to AmberAir 2. Possibility to choose pressure taps for heat recovery and coils sections 3. Possibility to choose both internal and external connections between sections 4. Possibility to add outdoor grills or hood on corner section 5. Modular power socket selection feature added 2017-01-31 Program updated to Version 5.6.1 build 10 Fixes: 1. Small fixes. 2017-01-30 Program updated to Version 5.6.1 build 9 Fixes: 1. Small fixes. 2017-01-27 Program updated to Version 5.6.1 build 8 Fixes: 1. Small fixes. 2017-01-25 Program updated to Version 5.6.1 build 7 Fixes: 1. Fixed selection of PM fans with VSD integrated on motor. 2. Small fixes. 2017-01-20 Program updated to Version 5.6.1 build 6 Fixes: 1. Added Bulgarian language support. 2. Small fixes. 2017-01-17 Program updated to Version 5.6.1 build 5 Fixes: 1. FlaktWoods fans dll have been updated. 2. Small fixes. 2017-01-13 Program updated to Version 5.6.1 build 4 Fixes: 1. Small fixes. 2017-01-10 Program updated to Version 5.6.1 build 3 Fixes: 1. Small fixes. 2017-01-10 Program updated to Version 5.6.1 build 2 Fixes: 1. Small fixes. 2017-01-03 Program updated to Version 5.6.1 build 1 Fixes: 1. Small fixes. 2016-12-23 Version 5.6.1 Changes: 1. Terminated the selection and production of the uniAir range AHU's 2. Zhiell-Abegg fans dll have been updated 3. Optimized calculation of steam humidifiers 4. Optimized section lengths for water and DX coolers 5. Price updates for units with control system 2016-12-21 Program updated to Version 5.6.0 build 10 Fixes: 1. Small fixes. 2016-12-19 Program updated to Version 5.6.0 build 9 Fixes: 1. Small fixes. 2016-12-15 Program updated to Version 5.6.0 build 8 Fixes: 1. Small fixes. 2016-12-14 Program updated to Version 5.6.0 build 7 Fixes: 1. Small fixes. 2016-12-13 Program updated to Version 5.6.0 build 6 Fixes: 1. Small fixes. 2016-12-12 Program updated to Version 5.6.0 build 5 Fixes: 1. Heat Pump calculation NAN error issue fix. 2. Small fixes. 2016-12-09 Program updated to Version 5.6.0 build 4 Fixes: 1. Small fixes. 2016-12-07 Program updated to Version 5.6.0 build 3 Fixes: 1. The rotary heat exchanger diameter, depth and gap load from issue fix. 2016-12-06 Program updated to Version 5.6.0 build 2 Fixes: 1. Small fixes. 2016-12-05 Program updated to Version 5.6.0 build 1 Fixes: 1. Base frame height and type of delivery - saving / loading issue 2016-12-02 Version 5.6.0 Changes: 1. Possibility to select Eurovent certified Hygienic Air Handling Units according to new Eurovent Hygienic Standard RS/6/C/011-2016. SmartAir SW50+ subrange H1 corresponds to Level 1 Hygienic Units and SmartAir SW50+ subrange H2 corresponds to Level 2 Hygienic Units. All metal surfaces inside those AHU’s meets the corrosivity class C3 in accordance with EN ISO 12944-2:1998 or they are made of aluminum. Drip trays are made of AISI 304 stainless steel. All non-metallic materials (sealants, gaskets, filters, etc.) meets EN ISO 846:1997 class 0 or 1. The selection software check all necessary requirements for Hygienic Units and give necessary hints how to correct selected unit to comply with this requirements. 2. Dimensions of doors and removable panels added to the printout. 3. Possibility to select silencers baffles with fiberglass-coated mineral wool. 4. Possibility to select cooling coils sections without droplet eliminator (air speed should be below 2,5m/s). 5. One of the possible SW50+ panel internal material changed from Zn RAL 7040 to AluZn 185(C4). 6. Improved coating for SW50+ panel external material. Now it corresponds to C4. 7. All drip trays connections changed to Ø40mm. 8. Possibility to select siphons for drip trays (both positive and negative pressure). 9. Possibility to select fan casing material. 10. Possibility to select painted frame for rotary heat exchangers. 11. Possibility to select painted frame for cross flow heat exchangers. 12. Possibility to select the height of the base frame and type of delivery (fixed to AHU or not fixed to AHU). 13. Possibility to select rotary heat exchanger with heat pump section with 3x230V voltage. 14. Changed dampers supplier. 15. HeatRun coils dll have been updated. 2016-11-11 Version 5.5.2 Changes: 1. Added VentMaster V5 Revit Plug-In file export support. Plug-In can be downloaded from http://www.salda.lt/en/products/category/download_page/. 2. Bug fixes 2016-07-15 Version 5.5.1 Changes: 1. Changed HEPA filters supplier. HEPA filters now available with galvanized steel or stainless steel frames. 2. Bug fixes 2016-07-01 Version 5.5.0 Changes: 1. Water heater coils supplier changed from Luvata and Roen Est to HeatRun. Roen Est coils are no longer available to select. Luvata coils available to select only with epoxy coating. 2. New component added ¢ Rotary heat exchanger with heat pump. Section consist of rotary heat exchanger, 2 coils and integrated heat pump. In winter supply coil works in heating mode, in summer supply coil works in cooling mode. 3. Added possibility to select accessories for water heating or cooling coils. 2016-05-27 Version 5.4.1 Changes: 1. Added possibility to select counter flow plate heat exchanger with different plate gaps. 2. Heatex cross flow plate heat exchanger are no longer available to select due to long lead time. 2016-04-15 Version 5.4.0 Changes: 1. New generation control system from SALDA with MCB controller. Cost efficient solution with huge possibilities. 2. Heatex rotary heat exchangers updated to most efficient E version. 3. Heatex plate heat exchangers updated to most efficient H2 version. 4. Hoval plate heat exchangers updated. 5. Added information whether heat exchanger section is monobloc or split. 6. AM-Premium module selection available for EC fans. 7. Optimized unit size selection depending on heat recovery type. 8. Small changes in Ecodesign requirements calculation. 9. Bug fixes. 2015-12-18 Version 5.3.0 Changes: 1. Eurovent Energy Efficiency Class 2016 calculation added. 2. Added possibility to select grease filters. 3. Added possibility to select activated carbon cartridges filters. 4. Added possibility to select EPA / HEPA filters. 5. Luvata coils dll have been updated. 6. Visual improvements. 2015-11-06 Version 5.2.0 Changes: 1. Calculation of the Ecodesign requirements for 2016 and 2018 years. 2. Fans. Possibility to order VSD (even for units without control system). 3. Fans. Possibility to order safety switch (even for units without control system). 4. Filters. Possibility to order filter contamination control (even for units without control system). 5. Damper. Possibility to order damper actuator (even for units without control system). 2015-10-02 Version 5.1.0 Changes: 1. Possibility to select counter flow heat exchangers. 2. Possibility to select direct-driven fan with PM motor. 3. New component added - angle section. Change airflow direction with right mouse button. 4. Side by side plate heat exchangers extended from 9-KR to 16-KR. 2015-09-11 Version 5.0.1 Changes: 1. UNI, PRO, TCP remote controllers are no longer available in control system selection. 2. Possibility to import VentMaster v4 files into VentMaster v5.0.1. 2015-07-01 Version 5.0.0. Release Visual improvements: 1. 3D view. 2. Detailed view of the unit in technical specification (view form the top). 3. Interactive change of the unitÆs dimensions according to selected properties. Functional improvements: Selection 1. Control system form is in the componentsÆ selection window. 2. It is possible to connect flexible connection or damper on the top of the fanÆs section. 3. Easy to change the type of the unit, now it is not necessary to create a new file for that. Export 1. Possibility to export technical specification to PDF file without additional software. 2. Exported DXF file supplemented by icons. Now it is easier to track each element in the drawing. Communication 1. New AHU order system. 2. Automatic software update. 3. The price of the unit is calculated automatically after recalculation of the unit. 4. Possibility to report about the bugs from the programme for logged in users. (Help->Bug report). We will be very grateful if other questions are still addressed ventmaster@salda.lt. ========================================================================== 2015-05-26 Version 4.3.0 Changes: - Added new rotary heat exchangers (Enventus, Eurovent certified) - Possibility to select plug fans with IE3 motors - Possibility to select EC plug fans with metal impeller - Possibility to select internal metal sheet material of panels for SmartAir SW50+ (Zn, Zn RAL 7040 or AISI 304) 2015-04-24 Version 4.2.2 Changes: - Possibility to select plug fans with metal impeller - Bug fixes 2015-03-20 Version 4.2.1 Changes: - SmartAir SW25 (Eurovent non certified model box) become uniAir SW25 - Added additional information about different model boxes casings in printout
down
Line below arrow

VentMaster V5 Revit 2016 Plug-In 1.00

(Herunterladen) 

VentMaster V5 Revit 2016 Plug-In.

Historie

2016/11/11 Version 1.00: -
down
Line below arrow

VentMaster V5 Revit 2017 Plug-In

(Herunterladen) 

Line below arrow

VentMaster V5 Revit 2018 Plug-In

(Herunterladen) 

Line below arrow

VentMaster V5 Revit 2019 Plug-In

(Herunterladen) 

Line below arrow

VentMaster V5 Revit 2020 Plug-In1.01.26

(Herunterladen) 

Line below arrow

VentMaster V5 Revit Plug-In installation guide

(Herunterladen) 

Line below arrow

MB Gateway FIRMWARE 1.13

(Herunterladen) 

Die neueste Version von MB Gateway-Firmware herunterladen.

Historie

2019-08-29 Version 1.13 1. Added additional transcyver settings 2. Fixed BACnet/IP subnet issue 3. Improved Modbus/TCP 2018-10-03 Version 1.12 1. Changed fuse bit settings. Firmware update is not available by bootloader. 2018-06-22 Version 1.11 1. AHU alarms and warnings notification system by email 2. Auto detect control board type (MCB/PRV) for BACnet/IP 2017-09-15 Version 1.10 1. BACnet/IP support added 2017-05-19 Version 1.09 1. SALDA AIR Android/iOS application compatibility added 2017-02-21 Version 1.08 1. Features: 1.1 Transceiver baudrate setting 1.2 Auto open "index.htm" files 1.3 Date/time synchronization with server 1.4 Service mode activation by pressing the button 2016 09 19 Version 1.07 1. Added datalogger feature 2. Transceiver function bugs fixed 3. FTP, HTTP bugs fixed 2016-07-01 Version 1.06 1. Added DHCP support
down
Line below arrow

MB Gateway WEB-Applikation (MicroSD-Inhalt) 1.13

(Herunterladen) 

Historie

2019-08-29 Version 1.13 Features 1. Updated user web page to support MCB 1.27 version. 2. Updated Adjuster/Service web pages to support MCB 1.27 version. 3. Changed device multicontrol window. 2018-11-02 Version 1.11.3 Bug fixes 1. Stand-alone Advanced web page. 2. Errors and Warnings via email configuration. Features 1. Updated Adjuster/Service web pages to support MCB 1.23 version. 2. Added Multihpc web page. 2018-07-10 Version 1.11.2 Bug fixes 2018-06-29 Version 1.11.1 Bug fixes 2018-06-22 Version 1.11 1. Support for MCB 1.20 firmware 2. AHU multicontrol improvement 3. Alarms and warnings notification system by email settings 2017-09-15 Version 1.10 1. MCB setpoint mode now shows temperature and fans percentage speed in home menu 2. Italian language fixes 2017-06-08 Version 1.09.2 Bug fixes 2017-05-22 Version 1.09.1 Bug fixes 1. PRV service part connection issue 2017-05-19 Version 1.09 2017-05-04 Version 1.08.3 Small bug fixes 2017-04-26 Version 1.08.2 Small bug fixes 2017-04-12 Version 1.08.1 Bug fixes 1. Modbus slave device recognition issue; 2017-02-21 Version 1.08.0 USER WEB: 1. Features 1.1 New alarms, their translations (LT,EN); 1.2 Enable/Disable hostname removed, hostname is now always enabled; 1.3 New advanced option in mb-gateway configuration window; 1.4 New menu with paging; 1.5 New humidity control page; 1.6 Dryness protection moved from “other“ to humidity; 1.7 Winter/Summer humidity control, boost control in humidity page; 1.8 New CO2 level page, select CO2 level option (only shown on specific settings); 1.9 Multicontrol – save all function; 1.10 Multicontrol – air handling unit count limited to 32, addresses 1-247; 1.11 Connection lost message of air handling unit is not found; 1.12 Percentage control, only active if fixed speeds option is set to “no”; 1.13 If percentage control is > 20, option to control temperature is shown. 1.14 MCB 1.10 support 2. Bug fixes 2.1 DHCP enabled/IP change sequence changed; 2.2 Bug where you couldn’t change password; 2.3 Other bugfixes (dhcp, multicontrol, tooltips, icons); ADVANCED WEB 1. Features 1.1 Multilanguage 1.2 Graphs: - Real time graphs - Time inverval graphs - 30 min interval graph 1.3 Logger variables: - Add/edit/delete variables 1.4 Logger group: - Add/edit/delete group 1.5 Transceiver: - Add/edit/delete transceiver variable - Add/edit/delete transceiver node 1.6 Support Bacnet/IP protocol configuration 1.7 MB-GATEWAY general configuration 1.8 Time synchronization MCB SERVICE/ADJUSTER WEB - MCB 1.10 support 2016-07-01 Version 1.06 1. Added DHCP support 2. Other bug fixes Version 1.05 - Version 1.04 1. Added a feature, so when CO2 or RH sensor values are lower than 1%, they aren’t shown in the main/status pages. 2. Fixed a bug where it would be possible to set the date in an incorrect format, for example, the date 31/02/2016 is for a month that only has 29 days; after the fix, the save button gets disabled, before the fix, the next month would be recalculated and the result would be 02/03/2016. 3. Added an SAF_flow and EAF_flow display near the status window in PRV. Version 1.03 1. Added multi-unit support. 2. Changed the design of the MB-gateway setup. 3. Multi-unit selection added to the main ventilation-control page and MB-gateway setup. 4. Multi-unit settings added to the MB-gateway setup. 5. MB-gateway configuration separated from the MB-gateway setup on a different page. 6. Added loading text message when selecting a new Unit in the ventilation control. Version 1.02 1. Fixed a bug, where some critical alarms weren’t shown. 2. Added SE, FI, DE translations for the MB-gateway. 3. Fixed a bug, where clicking reset in the alarm window wouldn‘t display the loading screen properly.
down
Line below arrow

MB Gateway BACnet/IP config files 1.10

(Herunterladen) 

Line below arrow

P-touch FIRMWARE 1.01.3

(Herunterladen) 

Die neueste Version von Ptouch-Bedienteil herunterladen.

Historie

2016-06-23 Version 1.01.3 1. Addedd MCB Full recirculation in MENU > Setpoints Version 1.01.2 - Version 1.01.1 1. MCB Date and Time, fixed bug for not setting time MCB Show Pa and m3/h for the adjuster when changing airflow values, if the fan’s control type is Pressure or Airflow PRV; 2. Fixed wrong values for the Heatexchanger and Heater types.
down
Line below arrow

P-touch update manual

(Herunterladen) 

Line below arrow
SALDA UAB
Ragainės g.100, Šiauliai LT-78109 LITHUANIA
Tel. +370 41 540 415 Fax. +370 41 540 417
office@salda.lt www.salda.lt